Nautilus E618 Скачать руководство пользователя страница 132

Страница: 132 / 137

132

3. Gently lift and remove the Console/Static Handlebar Assembly from the

Console Mast and disconnect the four cables (the Input/Output, Lift Motor,

Resistance Control, and Incline Control Cables) that come from the back

of the Console.
Note: Do not let the Cables fall down inside the Console Mast. If neces-

sary, use a rubber band or wire tie to secure them. This step may require

two people.

4. Using a #2 Phillips screwdriver, remove the four indicated screws from

the Console and remove the Static Handlebar.

Note: Be sure to observe how the cables route through the Static Handle-

bar from the Console before removing it to assist with re-assembly. Do not

crimp the cables.

5. Installation is the reverse procedure.

NOTICE:

Do not crimp the cables.

6. Inspect your machine to ensure that all hardware is tight and

components are properly assembled.

Do not use until the machine has been fully assembled and

inspected for correct performance in accordance with the

Owner’s Manual.

Содержание E618










































































































































Результаты поиска

Содержание E618

Отзывы:

Похожие инструкции для E618

Бренды по названию

Популярные бренды

Nautilus E618, Руководство по обслуживанию

Результаты поиска

Содержание E618

Отзывы:

Похожие инструкции для E618

Бренды по названию

Популярные бренды