Nautilus E618 Скачать руководство пользователя страница 122

Страница: 122 / 137

122

5. Using a 6mm hex key, loosen and remove the indicated hardware from

the Crank Arm and Leg, and set it safely aside for reassembly. On each

side of the machine, remove the Leg and Pedal together from the Rail

Assembly and set them safely aside for reassembly.

NOTICE:

This step may require two people.

6. Bend the edges of the Upper Shroud to disengage the inside tabs from

the Main Assembly, and slide the Shroud Cap and Top Shroud up the

Mast.

If you are not replacing the Upper Shroud—go to Step 9.

7. Remove the hardware (indicated) from the Mast. Gently pull the Mast

out and disconnect the cables. Set the hardware, Mast and Top Shroud

safely aside.

NOTICE:

Do not crimp the cables. This step may require two

people.

8. Using a small standard screwdriver, gently pry the cap off of the Crank

Arm.

Leg

Crank Arm

Upper Shroud

Содержание E618










































































































































Результаты поиска

Содержание E618

Отзывы:

Бренды по названию

Популярные бренды

Nautilus E618, Руководство по обслуживанию

Результаты поиска

Содержание E618

Отзывы:

Бренды по названию

Популярные бренды