Nautilus E618 Скачать руководство пользователя страница 111

Страница: 111 / 137

111

4. Using a 6mm hex wrench and a 13mm wrench, remove the indicated

hardware from the Lower Handlebar Arms and Pedals. Set the hardware

safely aside for reassembly.

Be aware that the Handlebar Arms will be loose and may

pivot when the hardware is removed. This step may require

two people.

Note: To assist with reassembly, observe how the Pivot Sleeve engages

flush with the Lower Handlebar Arm.

5. Disconnect the Cable from the Upper Handlebar that goes into the

Console Mast.

6. Using a 6mm hex wrench and a 13mm wrench, remove the hardware

from the Lower Handlebar Arms and the Arm Pivot Rod.

Be aware that the Handlebar Arms will be loose and may

pivot when the hardware is removed.

7. Remove the Handlebar Arm Assemblies and set them safely aside.

8. Using a 6mm hex wrench, remove the indicated hardware from the

Crank Arm and Leg.

9. Remove the Leg and Pedal together from the Rail Assembly and set

them safely aside for reassembly.

NOTICE:

This step may require two people.

Leg

Pedal

Leg

Crank Arm

Содержание E618










































































































































Результаты поиска

Содержание E618

Отзывы:

Nautilus E618, Руководство по обслуживанию, Страница: 111 / 137

Результаты поиска

Содержание E618

Отзывы: