Nautilus E618 Скачать руководство пользователя страница 87

Страница: 87 / 137

21. Using the 18mm socket and wrench and 18mm open end wrench,

loosen and remove the indicated hex head bolts (by arrow) that attach the

Incline Adjuster Assembly to the Lift Motor shaft. Set the bolts aside for

reassembly.

22. Remove the indicated hardware (by arrow) that attaches the Lift Motor

Assembly to the Frame.

Note: Do not rotate the Lift Motor Collar Nut on the Shaft while the Incline

Adjuster Assembly is not installed.

NOTICE:

Do not crimp any cables.

23. Remove old Lift Motor assembly, and discard.

24. Install the replacement Lift Motor assembly and hardware to the

Frame.

25. Connect the Lift Motor cable to the proper locations on the MCB.

Secure the cables with zipties.

Use the top screw to attach the green Lift Motor ground wire

to the Frame. Be sure not to crimp any cables.

26. Turn the power on.

Machine is on. Current is active. There is risk of electrical

shock.

27. From the Power Up Mode screen, push and hold down the PAUSE/

STOP button and Right arrow button for about 3 seconds to go into the

Console Setup Mode. The Console display will show the Edit Date screen

with the current setting.

28. Push the OK button 4 times until the Console displays the TOTAL RUN

HOURS screen.

29. Hold down the PAUSE/END button and Down button together for 3

seconds. The Console display shows the Firmware Version string.

Lift Motor Assembly

Incline Adjuster Assembly

Lift Motor Shaft

Lift Motor Collar Nut

Lift Motor Assembly

Содержание E618










































































































































Результаты поиска

Содержание E618

Отзывы:

Бренды по названию

Популярные бренды

Nautilus E618, Руководство по обслуживанию

Результаты поиска

Содержание E618

Отзывы:

Бренды по названию

Популярные бренды