Nautilus E618 Скачать руководство пользователя страница 23

Страница: 23 / 137

17. To adjust the Brake tension, loosen the 2 hex head bolts and

move the Servo Motor assembly until the closest point on the Brake

Magnet is within 3.0mm (1/8”) of the Flywheel. Tighten the bolts.

Note: If the cardboard is not 3mm (1/8”) thick, you can use the pages

of a paperback book to measure the gap. Approximately 36

pages (sheets) = 3mm.

18. Remove the cardboard from between the Brake Magnet and the

Flywheel.

19. Before fully attaching the Shrouds, power up the machine to

verify that the Magnet Arm can move freely, and that the Brake

Magnet and Flywheel do not touch at the maximum resistance level.

Machine is on. Current is active. There is risk of electrical

shock. Be sure to keep fingers clear of all pinch hazards

when you change the resistance level.

Brake Magnet

Flywheel

Servo Motor

20. Turn the power switch to off and disconnect all power and allow to sit for 5 minutes.

To reduce the risk of electrical shock or unsupervised usage of the equipment, always unplug the power cord from the

wall outlet and wait 5 minutes before cleaning, maintaining or repairing this machine. Place the power cord in a secure

location.

21. Installation is the reverse procedure.
Put the Left Shroud in position first to align the screws for the Right Shroud. Install the top screws first. Be sure the tabs in the Motorized Lift Cover

snap into the Side Shrouds.

NOTICE:

This step may require two people. Be sure not to crimp any cables.

Note: Self-tapping screws attach the Shrouds to the Frame.

Installation does not require the use of the crank puller. Be sure the Crank Arms are connected at 180° from each other.

22. Inspect your machine to ensure that all hardware is tight and components are properly assembled.

Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’s

Manual.

After adjusting the Brake Assembly, the resistance levels of the machine may be different. The user should adjust their workout levels accordingly.

Содержание E618










































































































































Результаты поиска

Содержание E618

Отзывы:

Бренды по названию

Популярные бренды

Nautilus E618, Руководство по обслуживанию

Результаты поиска

Содержание E618

Отзывы:

Бренды по названию

Популярные бренды