Nautilus E618 Скачать руководство пользователя страница 58

Страница: 58 / 137

6. Disconnect the indicated Cable (with arrow) from the Upper Handlebar

that goes into the Console Mast.

7. Using a 6mm hex wrench and a 13mm wrench, remove the hardware

from the Lower Handlebar Arm and the Arm Pivot Rod. The hardware on

both ends of the Arm Pivot Rod will need to be held to remove it.

8. Remove the Handlebar Arms.

9. Bend the edges of the Upper Shroud to disengage the inside tabs from

the Main Assembly, and slide the Shroud Cap and Upper Shroud up the

Console Mast.

10. Using a 6mm hex wrench, remove the hardware (indicated) from

the Console Mast. Slightly pull the Console Mast up and disconnect the

cables. Set the hardware aside for reassembly.

NOTICE:

Do not crimp the cables. Do not allow the cables to fall

down into the Main Unit or into the Console Mast. This

step may require two people.

11. Remove the Console Mast from the Upper Shroud.

12. Tie a length of string to the end of the Input/Output (I/O) Cable at

the base of the Console Mast. Hold the other end of the Input/Output

(I/O) Cable and carefully pull it out of the Console Mast so that the string

extends through the length of the Console Mast.

NOTICE:

Hold the Lift Motor Wire so that you do not pull it out of the

Console Mast. Do not crimp the cables.

Upper Shroud

Содержание E618










































































































































Результаты поиска

Содержание E618

Отзывы:

Похожие инструкции для E618

Бренды по названию

Популярные бренды

Nautilus E618, Руководство по обслуживанию

Результаты поиска

Содержание E618

Отзывы:

Похожие инструкции для E618

Бренды по названию

Популярные бренды