Nautilus E618 Скачать руководство пользователя страница 19

Страница: 19 / 137

1. Turn the power on to the machine.

2. Set the resistance level to the maximum setting on the Console.

3. Turn the power switch to off and disconnect all power and allow to sit for 5 minutes.

To reduce the risk of electrical shock or unsupervised usage of the equipment, always unplug the power cord from the

wall outlet and wait 5 minutes before cleaning, maintaining or repairing this machine. Place the power cord in a secure

location.

4. Using a #2 Phillips screwdriver, remove the 4 screws from each set

(right and left) of the Handlebar Shrouds. After removing the hardware,

pinch the Handlebar Shrouds to unsnap them from each other. Place

them safely aside.

5. Using a 6mm hex wrench and a 13mm wrench, remove the indicated

bolts from the Lower Handlebar Arms and Pedals. Set the hardware

safely aside for reassembly.

Be aware that the Handlebar Arms will be loose and may

pivot when the hardware is removed. This step may require

two people.

Handlebar Shrouds

Содержание E618










































































































































Результаты поиска

Содержание E618

Отзывы:

Похожие инструкции для E618

Бренды по названию

Популярные бренды

Nautilus E618, Руководство по обслуживанию

Результаты поиска

Содержание E618

Отзывы:

Похожие инструкции для E618

Бренды по названию

Популярные бренды