National Instruments NI 6612 Скачать руководство пользователя страница 53

Страница: 53 / 98

3-17

NI 6612 User Manual

To use the Large Range with 2 Counters method, configure the following:

•

DAQmx Create channel (CI-Frequency)

—Use this VI or function to create the channel.

•

CI.Freq.MeasMeth

—Set this property to Large Range with 2 Counters.

Note that this measurement method requires two counters:

•

Counter 0 paired with Counter 1

•

Counter 2 paired with Counter 3

•

Counter 4 paired with Counter 5

•

Counter 6 paired with Counter 7

By default, the counters measure the frequency on a default PFI terminal (refer to Chapter 5,

Counter Signal Routing and Clock Generation

, for more information) and use an onboard

100 MHz clock as the timebase. To change the signals used for this measurement, configure the
following:

•

CI.Freq.Term

—The signal-to-measure comes from an input terminal. To change the

signal-to-measure, set this property to a different terminal.

•

CI.CtrTimebase.Src

—To change the signals used as the counter timebase, set this

property to a different terminal.

High Frequency with 2 Counters

This measurement method requires two counters: Counter N and Counter M.

For this measurement method, the devices uses counter M to generate a pulse of duration T. The
device routes this pulse to Counter N. Counter N then counts the number of periods (

) of the

signal-to-measure during the pulse.

If the frequency of the signal-to-measure is

fx,

the duration of the pulse is given by:

Solving for

returns the frequency of the signal-to-measure:

P
f

---

P
T

---

Содержание NI 6612



































































































Результаты поиска

Содержание NI 6612

Отзывы:

Похожие инструкции для NI 6612

Бренды по названию

Популярные бренды

National Instruments NI 6612, Руководство пользователя

Результаты поиска

Содержание NI 6612

Отзывы:

Похожие инструкции для NI 6612

Бренды по названию

Популярные бренды