manualshive.com logo in svg

National Instruments NI 6612, Руководство пользователя

Поделиться
Скачать
National Instruments NI 6612 Скачать руководство пользователя страница 65

© National Instruments

|

3-29

NI 6612 User Manual

Trigger Settings

By default, the counter begins counting when you call DAQmx Start Task. To have the counter 
begin counting in response to a hardware trigger, use an Arm Start Trigger.

1.

Set ArmStart.TrigType to Digital Edge.

2.

Set ArmStart.DigEdge.Src to select what signal to use as the Arm Start Trigger.

3.

Set ArmStart.DigEdge.Edge to select the rising or falling edge of the signal.

Other Settings

You can filter noise on any PFI signal that is an input to the counter by enabling a filter. Refer 
to the 

PFI Filters

 section in Chapter 4, 

PFI

, for more information.

If you route the same PFI signal to multiple destinations, you should enable the Synchronization 
feature. Refer to Chapter 4, 

PFI

, for more information. 

Linear Position Measurement

In a linear position measurement task, the counter measures position using a quadrature encoder 
or two-pulse encoder.

Linear position measurements are similar to Angular position measurements. The main 
difference is that DAQmx can return the measurement in units of meters or inches instead of 
degrees or radians. 

To make an angular measurement, first call the DAQ Create Channel (CI-Position-Linear 
Encoder) VI or function. 

The settings for linear position measurements are the same as for angular position 
measurements.

Counter Output Applications

The NI 6612 can generate a wide variety of digital output signals. Counter output applications 
include:

•

Generating a series of one or more pulses.

•

Generating a periodic waveform with constant frequency and duty cycle.

•

Generating a periodic waveform with variable frequency and duty cycle.

•

Generating a complex digital waveform or timing pattern.

Содержание NI 6612



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды