National Instruments NI 6612 Скачать руководство пользователя страница 54

Страница: 54 / 98

3-18

ni.com

Chapter 3

Counters

Figure 3-19.

Frequency Measurement: High Frequency with Two Counters

With the known measurement time (

), which can be configured in CI.Freq.MeasTime, the

maximum error and maximum frequency error for this method are given by:

To use the High Frequency with 2 Counters method, configure the following:

•

DAQmx Create channel (CI-Frequency)

—Use this VI or function to create the channel.

•

CI.Freq.MeasMeth

—Set this property to High Frequency with 2 Counters

Note that this measurement method requires two counters:

•

Counter 0 paired with Counter 1

•

Counter 2 paired with Counter 3

•

Counter 4 paired with Counter 5

•

Counter 6 paired with Counter 7

…

rce

nter M

rce

nter N

ign

l to

asu

ign

l to

asu

re (f )

nter

Time

bas

e (f )

Maximum Error (%)

-------------

100%

Maximum Frequency Error (Hz)

---

Содержание NI 6612



































































































Результаты поиска

Содержание NI 6612

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI 6612, Руководство пользователя

Результаты поиска

Содержание NI 6612

Отзывы:

Бренды по названию

Популярные бренды