National Instruments NI 6612 Скачать руководство пользователя страница 51

Страница: 51 / 98

3-15

Low Frequency with 1 Counter

For this method, the device detects the first full period of the signal-to-measure. The counter
measures the duration of this period by counting the number of cycles (

) of the timebase.

DAQmx reads

, and uses the known frequency of the timebase (

)

, to calculate the frequency

of the input signal (

) as:

Figure 3-17.

Frequency Measurement: Low Frequency with One Counter

The maximum error and maximum frequency error for this method, are given by:

To use the Low Frequency with 1 Counter method, configure the following:

•

DAQmx Create channel (CI-Frequency)

—Use this VI or function to create the channel.

•

CI.Freq.MeasMeth

—Set this property to Low Frequency with 1 Counter.

By default, the counter measures the frequency on a default PFI terminal (refer to Chapter 5,

Counter Signal Routing and Clock Generation

, for more information) and use an onboard

100 MHz clock as the timebase. To change the signals used for this measurement, configure the
following:

•

CI.Freq.Term

—The signal-to-measure comes from an input terminal. To change the

signal-to-measure, set this property to a different terminal.

•

CI.CtrTimebase.Src

—To change the signals used as the counter timebase, set this

property to a different terminal.

------

…

Fre

ency of

Interv

l Me

asu

red

DAQmx

rt T

ign

l to

asu

re (f )

nter

Time

bas

e (f )

Maximum Error (%)

–

-------------

100%

Maximum Frequency Error (Hz)

–

-------------

Содержание NI 6612



































































































Результаты поиска

Содержание NI 6612

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI 6612, Руководство пользователя

Результаты поиска

Содержание NI 6612

Отзывы:

Бренды по названию

Популярные бренды