National Instruments NI 6612 Скачать руководство пользователя страница 56

Страница: 56 / 98

3-20

ni.com

Chapter 3

Counters

Channel Settings

By default, the counter:

•

measures pulses on a default PFI terminal. Refer to Chapter 5,

Counter Signal Routing and

Clock Generation

, for more information.

•

measures a high pulse. That is, the counter begins measuring the time from a rising edge to
the next falling edge.

•

returns the measurement in the unit of seconds.

You can change these behaviors by configuring DAQmx Channel properties:

•

CI.PulseWidth.Term

—The signal-to-measure comes from an input terminal. To change

the signal-to-measure, set this property to a different terminal.

•

CI.PulseWidth.StartingEdge

—Specifies on which edge, rising or falling, to begin the

measurement.

•

CI.PulseWidth.Units

—Specifies the units of the measurement.

Timing Settings

The timing settings determine when the device measures the signal. Figure 3-20 shows an
example of On-Demand timing.

On-Demand (No Sample Clock)

By default, the counter uses On-Demand timing. The following sequence of events describe On
Demand timing:

Software calls DAQmx Start Task.

The device measures the first full pulse on the signal-to-measure.

The device waits until you call DAQmx Read. The device ignores the signal-to-measure
while waiting.

The device returns the measurement.

The device then measures the next full pulse on the signal-to-measure.

Steps 3, 4, and 5 are repeated.

Содержание NI 6612



































































































Результаты поиска

Содержание NI 6612

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI 6612, Руководство пользователя

Результаты поиска

Содержание NI 6612

Отзывы:

Бренды по названию

Популярные бренды