National Instruments NI 6612 Скачать руководство пользователя страница 49

Страница: 49 / 98

3-13

NI 6612 User Manual

Figure 3-15.

Frequency Measurement: Sample Clock with Averaging

At each sample clock, the device stores

and

in a buffer. DAQmx reads these values, and

uses the known frequency of the timebase (

), to calculate the frequency of the input signal (

)

as:

The maximum error and maximum frequency error for this method, are given by:

To use the Sample Clock (with Averaging) method, configure the following:

•

DAQmx Create channel (CI-Frequency)

—Use this VI or function to create the channel.

•

DAQmx Timing (Sample Clock)

—Use this VI or function to set the number of samples,

sample clock source, and other properties.

•

CI.Freq.EnableAveraging

—Set this property to True.

By default, the counter measures the frequency on a default PFI terminal (refer to Chapter 5,

Counter Signal Routing and Clock Generation

, for more information) and use an onboard

100 MHz clock as the timebase. To change the signals used for this measurement, configure the
following:

•

CI.Freq.Term

—The signal-to-measure comes from an input terminal. To change the

signal-to-measure, set this property to a different terminal.

ign

l to

asu

re (f )

nter

Time

bas

e (f )

mple

Clock (f )

DAQmx

rt T

T1 T2

1 7

T1 T2

1 7
2 10

T1 T2

1 7
2 10
1 6

ffer

mple 2

mple

mple 1

------

Maximum Error (%)

---

–

----------------------------

100%

Maximum Frequency Error (Hz)

---

–

----------------------------

Содержание NI 6612



































































































Результаты поиска

Содержание NI 6612

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI 6612, Руководство пользователя

Результаты поиска

Содержание NI 6612

Отзывы:

Бренды по названию

Популярные бренды