background image

Napco iSecure Security System                         

All technical manuals are available in PDF format at 

tech.napcosecurity.com

 

59 

Cloud Web Portal for later retrieval, if needed. 

 

  Restore From Backup 

  Click to restore the iSecure Cloud Web Portal to the previ-

ous  configuration  that  will  appear.    To  update  the  Go-

Anywhere Hub, a full download must be performed after the 

restoral.   

 

  BACKUP Z-Wave Configuration Data 

  Click to back up all Z-Wave enrolled devices and program-

ming into the iSecure Cloud Web Portal. 

 

  RESTORE Z-Wave Configuration Data 

  Click  to  restore  all  Z-Wave  enrolled  devices  and  program-

ming into the Z-Wave device.   

 

  Last backup 

  Displayed under the appropriate button, this is the date and 

time (in 24-hour military format) the last complete and suc-

cessful backup was performed for the associated configura-

tion.    The  backup  is  sent  from  the  Hub  to  the  Cloud  Web 

Portal.   

 

 

ISECURE DEVICE VERSIONS & STATUS 

  Many  different  types  of  microprocessors  and  firmware  are 

used within the iSecure system, some located within the Go

-Anywhere Hub, others within each iSecure device.  Some 

devices are required, some are optional; all are listed in this 

screen to display their related firmware for each.  Use this 

screen  to  ensure  that  the  firmware  is  the  latest  version 

(click the 

Scan

 button to retrieve the latest data).  To manu-

ally update firmware, see the section "

FIRMWARE  DOWN-

LOAD

"  on page 57.  

 

 

 

 

 

 

 

 

 

 

 

 

 

  Entries located at the top of this screen include the various 

Go-Anywhere Hub hardware and firmware versions, includ-

ing:   

 

"

EZ_DATABASE

"   refers  to  the  iSecure  Cloud  Web 

Portal database version.   

 

"

ISECURE  PANEL

"  refers to the microprocessor ver-

sion  within  the  Go-Anywhere  Hub  that  controls  most  of 

the local alarm functions (arming/disarming, etc.).   

 

"

RadioFirmware  Version

"  refers to the microproces-

sor within the Go-Anywhere Hub that controls the radio 

communications  between  the  Hub  and  the  wireless  de-

vice(s).   

 

"

RadioHardware  Version

"  refers to the version of the 

LTE  Radio  PC  board 

that  is  plugged  into  the  Go-

Anywhere  Hub  motherboard.    This  PCB  controls  the 

LTE radio communication (reporting) functions.   

Other iSecure Cloud Web Portal Screens (cont'd)  

 

INTEGRAL KEYPAD

 (reserved for future use) 

 

RF  RECEIVERS1

  refers  to  the  integral  Hub  319MHz 

receiver  firmware  that  controls  those  devices,  including 

the  window/door  transmitters,  passive  infrared  motion 

sensors, etc. 

 

RF  RECEIVERS2

  refers  to  the  integral  Hub  900MHz 

receiver  firmware  that  controls  those  devices,  including 

the keypads and other 900MHz peripherals. 

 

  Other entries include the versions and current status of the 

various  optional  iSecure  devices  that  can  be  added  to  the 

system (sirens, keypads, sensors, etc.).   

 

  Device Name / Device Type 

  Description of each upgradable module or firmware version 

that exists or can exist within the iSecure system.  The text 

names are derived from the current Hub firmware.   

 

  M1 Version / Boot Loader / M2 Version 

  Displays  the  version  of  the  Hub  firmware  for  microproces-

sor #1 and (under its own column) #2.  The Boot Loader is 

the firmware that controls the remote download/upload pro-

cesses.   

 

  RFID 

  Each wireless device (for example, a keypad) has a unique 

factory programmed ID code that distinguishes itself to the 

Hub.  For example, "155E57:F".  The first six characters of 

the ID code are displayed here.   

 

  Learn Status 

  Indicates whether the device was correctly and successfully 

entered  into  the  Hub  programming.   

Note: 

  Although  the 

device  may  be  been  correctly  configured  in  the  iSecure 

Cloud  Web  Portal  and  downloaded  into  the  Go-Anywhere 

Hub  without  apparent  errors,  a  "Learn  Successful"  status 

always  requires  a  complete  two-way  synchronization  and 

acknowledgement  "handshake"  between  the  Hub  and  the 

device.  For example, a device with a "Learn Unsuccessful" 

status  may  not  have  been  powered  during  the  learn  pro-

cess, and thus is not successfully learned into the system.  

Note:

    Every  re-learn  process  also  refreshes  the  version 

information. 

  See "

FIRMWARE DOWNLOAD

" on page 57 for important 

information about the firmware update process.   

Содержание iSecure ISEC-EXTANT-KIT





















Отзывы: