LIBRA LIB-P432EX Series Programming Instructions
NAPCO Security Systems
Page 10
Key Fob Transmitters as Zone Input Devices
(Refer to display above: press the PRIOR button to go backwards).
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button =
point 2; A1 = point 3; A2 = point 4. Up to 64 key fobs (using 1 button) or 32 key fobs (using 2 buttons) or
16 key fobs (using all 4 buttons) or any combination up to a maximum of 64 controlled zones can be as-
signed, providing multiple wireless panic buttons on a system, each reporting to a Central Station or a
pager and/or annunciating on a keypad the key fob zone number with a description.
To assign a key fob
to a zone:
program the key fob as you would a transmitter, entering the key fob's ID code, check sum and
point number at the appropriate zone. The "Quick Method" is not allowed. The zone may be hardwired to
an electrical sensor as well as assigned to a key fob (either one will activate the zone alarm output).
NOTE:
If assigning a key fob to a zone, the "ON/OFF" buttons on the key fob will no longer arm/disarm the
system. The key fob is converted to a "panic only" device.
Enter Zone Descriptions
•
For each zone, enter a description of up to two lines. Press
u
to save each description.
•
See page 41 for instructions for entering characters and numbers for the zone descriptions.
•
To proceed to the next description, place the cursor under the Zone Number (e.g. "1") and
press the number that corresponds to the zone. Program new description as above.
NOTE:
Zone Descriptions can only be en-
tered through the
GEM-DXRP1/GEM-DXK1 Keypad or by using the Napco Quickloader Software.
See
Easy Menu Programming
Worksheet
for available zone description characters.
Enter Date
(Press
w
to set cursor).
•
Enter the current date in the format MM/DD/YY. (MM = month, DD = day and YY = year.
•
Press
u
to save. Press
NEXT ("
r
" or
p
)
to proceed.
Enter Time
(Press
w
to set cursor.)
•
Enter the current time in format HH:MMA/P, where HH=hours (01–12); MM=minutes (00–59).
•
Select AM or PM by pressing any number button.
•
Press
u
to save. Press
NEXT ("
r
" or
p
)
to proceed.
Dealer Code
•
Directly enter the Dealer Code (default = 456789), using
0
through
9
buttons.
•
Press
u
to save. Re-enter the Dealer Code to verify the previous code. Press
u
to save.
•
Press
NEXT ("
r
" or
p
)
to proceed.
Test Timer
•
Select day(s) by simply erasing the unwanted days. Move the cursor over the day and
press any number key to erase/restore the day. For example, "Monday" and "Friday" will
appear as: "•
M
•
•
•
F
•"
•
Enter Time (in 24 hour format) by moving cursor under the left H and pressing two digits to over-
write the existing default of 00.
Note:
Midnight is 00:00. Enter minutes by continuing to enter
data or if just updating minutes move the cursor under the left M and enter the two digits to over-
write the existing default of 00. Use
w
as right cursor one position.
(Direct Entry)
Enter Date
( / / )
(Direct Entry)
Enter Time
( : )
D e a l e r C o d e
4 5 6 7 8 9
D E A L E R C O D E
R E - E N T E R
CLEAR PROGRAM:
Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press
y
to enter the Address Program Mode; (b) access Location 2285 (Clear Program) or 2286 (Cold Start); (c) press
u
and then (d)
press
y
to exit the Dealer Program Mode. A “
SYSTEM TROUBLE/E09-00 SERVICE
” will occur. Press
y
to silence the keypad.
Clear Dealer Program (Erases Dealer Program)
Use this feature to erase the Panel Program, while maintaining Scheduled Data and Zone Descrip-
tions. Access address 2285 and press
u
. Data entry is not allowed.
NOTE:
Enter Easy
Menu Driven Program Mode to reprogram system.
Cold Start (Erases Entire Program)
This erases all programmed data (Dealer Program, Zone Description Data and Schedules).
Access address 2286 and press
u
. Data entry is not allowed.
NOTE:
Some features
(schedules) can only be programmed again with the Downloading Software.
DATA
ENTRY
AUX 1/AUX 2
OPTIONS
0
None
1
Relay Group 1 Toggle
2
Relay Group 2 Toggle
9
Keypad Panic
A
Keypad Aux.
B
Instant
C
PGM2 Ouput Toggle
D
Access on PGM2 Output
E
Arm STAY
F
Interior Button
(Direct Entry)
0 1 -
EXIT DEALER PROGRAM MODE:
This completes the custom default program. Press
y
to enter the Direct Address Program
Mode for further programming or press
y
once again to end all programming and resume normal keypad operation.
2 2 8 5 X X H
2 2 8 6 X X H
T E S T T I M E R
S M T W T F S H H : M M
Содержание GEM-DXK1
Страница 56: ...LIBRA LIB P432EX Series Programming Instructions NAPCO Security Systems Page 56 LIB P432EX WIRING DIAGRAM...
Страница 57: ...NAPCO Security Systems LIBRA LIB P432EX Series Programming Instructions Page 57 LIB P432EXT WIRING DIAGRAM...
Страница 58: ...LIBRA LIB P432EX Series Programming Instructions NAPCO Security Systems Page 58 LIB P432EXT 230 WIRING DIAGRAM...
Страница 59: ...NAPCO Security Systems LIBRA LIB P432EX Series Programming Instructions Page 59 NOTES...
