NAPCO GEM-DXK1, Инструкция по программированию

Страница: 6 / 60

LIBRA LIB-P432EX Series Programming Instructions NAPCO Security Systems
Page 6
Total Number of Zones in Area 1 (New Program Only)
•
Enter the total number of zones to be programmed for Area 1.
•
Valid entries are from 01 to 32. Directly enter the total number of zones, including leading zeros.
•
The system is based on groups of 4 zones each (after the first 8 zones), and will automati-
cally round up to the next group of 4. For example, if you enter 18, it will automatically con-
vert this to 20 zones. Press
u
to save. Press
p
to proceed.
Panel Zone Doubling (New Program Only)
•
To double the number of hardwired panel zones from 8 to 16, press p .
•
If Panel Zone doubling is not desired, press q .
•
The 16 zones will remain EOL terminated zones, requiring Normally Closed devices only.
•
Refer to Wiring Diagram and Installation Instructions for wiring instructions
Fire Zones in Area 1 (New Program Only)
•
Enter the zone number of any Fire Zones (including 2-wire, 4-wire or wireless).
•
Valid entries are from 01 to 32.
•
Directly enter each zone number, including leading zeros, and press
u
to save, and then re-
peat for any additional zone(s). Press
p
to proceed.
Local or Central Station Reporting System (New Program Only)
Press p for all zones to report; press q for local system
Exit/Entry Zones in Area 1 (New Program Only)
•
Enter the zone numbers of zones to be used as Exit/Entry zones.
•
Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•
Press
u
to save and repeat for any additional zone(s); press
p
to proceed.
NOTE: Exit/Entry Entry time of 30 seconds will automatically be programmed.
Interior Zones in Area 1 (New Program Only)
•
Enter the zone numbers to be used as Interior Zones.
•
Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•
Press
u
to save and then repeat for any additional zone(s).
•
Press p to proceed.
•
All Interior zones will also be automatically programmed as “Exit/Entry Follower” and as "Power
Up Delay" zones.
24 Hour Zones in Area 1 (New Program Only)
•
Enter the zone numbers of zones to be used as 24 Hour zones.
•
Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•
Press
u
to save and repeat for any additional zone(s); press p to proceed.
NOTE: 24 Hour Zones will automatically be programmed as audible (Burg Output).
(Direct Entry)
# o f Z n s i n A r e a 1
E n t e r # Z o n e s X X
(Press YES or NO)
E Z Z o n e D o u b l i n g
E n a b l e d ? Y / N
(Direct Entry)
F i r e Z o n e s
E n t e r Z o n e # ° °
(Press YES or NO)
R e p o r t A l l Z o n e s
T o C e n t r a l ? Y / N
(Direct Entry)
E x i t / E n t r y Z o n e s
E n t e r Z o n e # X X
(Direct Entry)
I n t e r i o r Z o n e s
E n t e r Z o n e # X X
(Direct Entry)
2 4 H o u r Z o n e s
E n t e r Z o n e # ° °
GEM-DXRP1 / GEM-DXK1 Keypad Easy Program Menu
To create a custom program using the GEM-DXRP1 / GEM-DXK1 keypad, simply answer the following questions and record your informa-
tion on the
Easy Menu Programming Worksheet . In each of the following steps, press w to set cursor, the NEXT ("
r
" or p ) to go
forwards, the PRIOR ("X" or
q
) to go backwards,
u
to save and
y
twice to exit at any time.