MUTOH Rockhopper 3 Extreme Скачать руководство пользователя страница 124

Страница: 124 / 137

User’s Guide Rockhopper 3 Extreme

CHAPTER 7 : TROUBLESHOOTING

124

AP-75198– Rev. 1.2

(4) The printer does not print and an error is generated after data has been sent from a computer.

N°

Possible cause

Solutions

References

The model setting of the computer
is not correct.

Make sure that the model
settings on computer and
printer are the same.

Refer to Connecting the printer to
your PC

The interface setting or command
mode on computer and printer do
not match.

(5) Printouts are partially blurred or missing.

Notes

You may not obtain reasonable quality with media other than recommended media.

N°

Possible cause

Solutions

References

The media is damped.

Replace with new media.

Refer to Replacing media

You used folded, creased or curled
media.

Check the media for curling or lift
off.

Use the recommended
media.
When using media other
than recommended
media, set the following
items in the media setting
menu.
Media
HeadHeight
Stiff

Refer to Media type
Refer to Menu Overview

(6) Printing position is not correct (some positions are not printed.)

N°

Possible cause

Solutions

References

The loading position of the media
is not correct.

Load the media correctly.

Refer to Loading media

You used the scale or mirror
setting.

Turn off the scale or
mirror setting, or make the
setting again.

Refer to Menu Overview

You set the origin or starting
position.

Turn off the origin or
starting position setting, or
make the setting again.

Refer to Menu Overview

Содержание Rockhopper 3 Extreme










































































































































Результаты поиска

Содержание Rockhopper 3 Extreme

Отзывы:

Похожие инструкции для Rockhopper 3 Extreme

Бренды по названию

Популярные бренды

MUTOH Rockhopper 3 Extreme, Руководство пользователя

Результаты поиска

Содержание Rockhopper 3 Extreme

Отзывы:

Похожие инструкции для Rockhopper 3 Extreme

Бренды по названию

Популярные бренды