manualshive.com logo in svg

Musicmakers BALLAD HARP KIT, Руководство по сборке

Поделиться
Скачать
Musicmakers BALLAD HARP KIT Скачать руководство пользователя страница 8

651-439-9120

8 

www.harpkit.com

____17. Fit the soundboard using the same techniques as 

you used to fit the back panel in steps 13 and 14. 
There will be a couple slight differences that you will 
need to pay attention to. There is a greater risk to 
nail through the outside face when you are install-
ing the soundboard. There are two things you can 
do to help avoid this from happening. 

1) Make sure that you are paying attention to the 
angle that you are installing the nails/staples. Make 
sure to match the angle of the sides of the frame. (fig. 
17a)

2) Instead of marking centerlines  for the nail/staple 
guidelines in step 14; mark your guidelines about 1/3 
of the way from the inside edge. (fig. 17b) 

It is very difficult to make a seamless repair when 
you punch through the sides. If you pay attention to  
these two steps, it should prevent any issues. 

Angle of Nail/
Staple should 

match the side 

of frame

Mark your guidelines 1/3 of 

the way from the inside edge

FIG. 17A

FIG. 17B

____18. Test the bottom front trim strip in place and mark holes where screws will be. Do NOT nail/

staple whithin 1/4” of where these holes will be. (fig. 18a)

You will also need to attach the soundboard scrap. It is best to avoid nailing/stapling in the 
middle of the scrap as that is where the pillar screw will come in. Put a nail/staple on each side 
of the soundboard scrap. (fig. 18b)

Don’t punch through the 

sides of the frame!

____16. Apply a liberal amount of glue to the frame and proceed to nail/staple the back panel in place. 

Make sure to match the angle of the nail/staple to the angle of the sides of the soundbox, so that 
it does not go through the side. This will be more critical when installing the soundboard, as 
it has the risk of punching through the ouside face of the side of the frame.  Start by installing 
one nail at each end of the panel to keep it aligned as you add more nails down each side and 
across the bottom. Place your nails or staples about 1-1/2” to 2” apart.  (fig. 16a, b, c)

This step will go eas-
ier with an extra set 
of hands to speed 
things up before the 
glue dries. Do NOT 
nail/staple along the 
top block, as there is 
no trim to cover this 
area. (fig. 16d) You 
will need to clamp 
the back to the top 
block to be sure that 
it gets held down. 

FIG. 16A, B

FIG. 16C, D

NO Staples 

or Nails

Содержание BALLAD HARP KIT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды