manualshive.com logo in svg

Musicmakers BALLAD HARP KIT, Руководство по сборке

Поделиться
Скачать
Musicmakers BALLAD HARP KIT Скачать руководство пользователя страница 19

651-439-9120

19 

www.harpkit.com

FIG. 43G, H, I

____44. Use masking tape to mark a depth stop on your 3/8” 

drill bit, at a 1-1/4” depth. (fig. 44a) This drill bit is not 
included in your hardware pack. However, it’s a com-
mon size in most drill bit sets.

HINT: 

The 3/8” drill bit will tend to wander as you are drilling. If you first drill the hole 

with a 5/32” drill bit, it will help stop the bit from wandering. 

p

____45. Using the guideline you just marked on the top of the arched 

cap block and the under side of the neck; use an awl to tap  a 
starting hole at the centerpoint. This will act like a pilot hole 
to help keep the drill bit from wandering. (fig. 45a, b) 

Now drill a hole to the depth of your tape where you made 
your awl mark on both the arched cap block and the neck. 
Rock the drill front to back about 10 degrees to give the dow-
el potential for a little movement. (This movement will help 
when attaching the bottom of the pillar.) DO NOT ROCK 
THE DRILL BIT LEFT/RIGHT. (fig. 45c)

FIG. 44A

FIG. 45B, C

HINT: 

Secure the neck in a padded vise before drilling the hole for the dowel.

p

FIG. 45A

Содержание BALLAD HARP KIT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды