Musicmakers BALLAD HARP KIT Скачать руководство пользователя страница 10

Страница: 10 / 32

651-439-9120

www.harpkit.com

____23. Sand the access holes in the back panel first using 120

grit, and then again with 180 grit sandpaper. Be sure
to clean up the entire perimeter of each hole. This will
make for more comfortable handling once the harp is
finished. (fig. 23a) Then use an orbital sander to

light-

sand the entirety of the back, soundboard, and sides

using 220 grit sandpaper. Make sure to take extra care
to hold the sander flat. (fig. 23b, c)

NOTE:

Be careful

when you are sanding.
The back has a VERY
thin hardwood veneer,
and it is very easy to sand
through the veneer.
Also, there is no need

for heavy sanding.

FIG. 23A

FIG. 23B, C

INSTALLING THE TRIM

____21. If you haven’t already done so, this is the time to

remove the overhang from the top and bottom of the
back and soundboard. (fig. 21a)

Also use this time to double check that all the nails/
staples are driven down slightly below the surface of
the back and soundboard.

____22. Remove the excess overhang from along the sides of the frame as well. There are several options

for removing the excess. You can use a fine tooth hand saw, a hand plane, a palm belt sander,
or a sanding block. (fig. 22a, b, c, d)

FIG. 21A

FIG. 22A, B

FIG. 22C, D

Содержание BALLAD HARP KIT

































Результаты поиска

Содержание BALLAD HARP KIT

Отзывы:

Бренды по названию

Популярные бренды

Musicmakers BALLAD HARP KIT, Руководство по сборке

Результаты поиска

Содержание BALLAD HARP KIT

Отзывы:

Бренды по названию

Популярные бренды