manualshive.com logo in svg

Musicmakers BALLAD HARP KIT, Руководство по сборке

Поделиться
Скачать
Musicmakers BALLAD HARP KIT Скачать руководство пользователя страница 21

651-439-9120

21 

www.harpkit.com

FIG. 48C, D

FIG. 48E, F

____49. Place the body of the harp on its back on your workbench. Hold the neck and pillar assembly 

in place on the body. Check the fit at the back of the neck where it slides into the cap block, 
and then check how the bottom of the pillar meets the base block. Follow the photos and make 
minor adjustments as needed to achieve a good fit. 

FITTING THE NECK AND PILLAR TO THE BODY

NOTE:

  

We do our best to ensure the neck and pillar will fit the body of your harp, before it 

leaves our shop. However, as a result of the building process, sometimes slight variations 
can occur that will require you to adjust the final fitting at the end of the building process. 

p

REMINDER:

 The joint between the back of the neck and the top of the body will remain 

dry --no glue. the reason is to create a sort of “knuckle” that allows the harp to flex slightly 
under string tension over time. It also allows you to take the neck/pillar assembly off the 
body of the harp in the future, by simply removing the strings and the screws at the bottom 
of the pillar. That permits you to  make repairs, add decorations, or refinish the harp easily, 
as necessary, down the road. It is one of the best features we have incorporated into our 
harp designs, saving much time and consternation in some cases. 

p

Fig. 49a shows a perfect fit. If yours looks 
like this, then proceed to step 50. 

FIG. 49A

Содержание BALLAD HARP KIT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды