manualshive.com logo in svg

Musicmakers BALLAD HARP KIT, Руководство по сборке

Поделиться
Скачать
Musicmakers BALLAD HARP KIT Скачать руководство пользователя страница 18

651-439-9120

18 

www.harpkit.com

____43. Stand the harp up, leaning it against your work table, so you can check the fit of the back of the 

neck on top of the soundchamber. Make a mark at about the center of the top block. (fig. 43a) 
Then using a straight edge, make a long angled diagonal mark. (fig. 43b) This will serve as a 
guide as you drill a hole for the dowel to connect the shoulder to the body of the harp. Match 
this angle as you are drilling. It will also help you make sure the neck and pillar match up cor-
rectly once the dowel is installed. Make a mark on the opposite side as well. (fig. 43c)

FIG. 43A, B, C

Draw your hash line from each side of the arch 
cap to the top. (fig. 43d) Connect the marks 
across the arched cap using a straight edge. (fig. 
43e) Then mark the center of the line you just 
made. (fig. 43f)

FIG. 43D

Repeat this process on the under side of the neck. (fig.43g, h, i) 

FIG. 42A, B, C

FIG. 43E, F

Содержание BALLAD HARP KIT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды