manualshive.com logo in svg

Musicmakers BALLAD HARP KIT, Руководство по сборке

Поделиться
Скачать
Musicmakers BALLAD HARP KIT Скачать руководство пользователя страница 26

651-439-9120

26 

www.harpkit.com

____58. Install the 10 large threaded bridge pins into the lower row of holes drilled in the neck in the 12 

bass end holes. Tap them partially in with a hammer and then turn them in with a 3/32” allen 
wrench until the top is about 5/8” above the surface of the wood. Use the 5/8” spacing guide to 
check the pin height. (fig. 58a, b) 

Install the remaining 24 medium bridge pins into the smaller holes on the lower row. Use the 
5/64” allen wrench to adjust the height to 5/8” above the harp neck.

NOTE:

  

Our threaded 

bridge pins are adjustable 
in depth, allowing you to 
change the space between 
the harp string and the 
wood surface of the neck, 
using the allen wench 
provided. This will be 
important later when you 
want to install sharping 
levers. 

p

____59. Turn the neck/pillar assembly over so the bridge 

pins are hanging over the edge of your work 
table, but the neck is still firmly supported. Use 
the brass driver in your hand drill to push and 
turn the 34 threaded black tuning pins into the 
upper row of holes in the neck, from the oppo-
site side of the bridge pins. DO NOT LUBRICATE 
the threads of these tuning pins! They  need to fit 
tightly in the wood to keep the strings in tune by 
friction. When you push firmly as you turn them, 
they will drive in quite quickly, skipping threads. 
Don’t rely on the microthreads to seat these pins. 
That will take too long, and it heats up the pins 
to an extreme temperature. Push hard and turn 
slowly until the narrow end extends about 5/8” 
beyond the surface of the wood. (fig. 58b) Use the 
spacing guide to check these pins as well.  

FIG. 58A

FIG. 58B

Содержание BALLAD HARP KIT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды