manualshive.com logo in svg

Musicmakers BALLAD HARP KIT, Руководство по сборке

Поделиться
Скачать
Musicmakers BALLAD HARP KIT Скачать руководство пользователя страница 30

651-439-9120

30 

www.harpkit.com

REMEMBER: 

Do not 

accumulate a lot of 
windings of string 
around the tuning pins, 
especially with the thick 
bass (low) strings. If you 
have that problem, turn 
the tuning pin backward 
to unwind the string, 
then pull more of the 
string through the hole 
and tighten again. 

p

FIG. 10A

Cross your 

windings!

TUNING

____11. When all the strings are installed, you can begin tuning the strings up to pitch. Expect it take 

around 50 tunings before the harp will fully stabalize. We recommend tuning it two or three 
times a day. Persevere, and be patient! It should get better each day. 

The strings should all be tuned to the natural C major scale (white keys on the piano.) All the 
red strings will be C notes and the blue strings with be F notes. 

Many people are not certain if they are tuning their harp strings to the correct octave. Tuning 
the strings an octave too low will result in flabby harp strings that don’t provide much volume. 
Tuning the strings too high will cause strings to break. To make sure you are tuning your harp 
strings to the correct octave, you can double-check the pitch on our website with our “online 
tuner” at www.harpkit.com/freetuner.

You can also check your string chart. You’ll see notes listed with a number after them (C4 or D5 
for an example.) This is a standard numbering system used to identify the octave of any given 
note. Middle C on the Piano is C4. The number changes at every C. (fig. 11a)

FIG. 11A

Содержание BALLAD HARP KIT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды