manualshive.com logo in svg

Musicmakers BALLAD HARP KIT, Руководство по сборке

Поделиться
Скачать
Musicmakers BALLAD HARP KIT Скачать руководство пользователя страница 31

651-439-9120

31 

www.harpkit.com

Caring for your Ballad Harp

 

TUNING TIPS -- 

It is best to tune the harp with all sharping levers fliped down (disengaged), so there 

will be no interference from the levers. Please note that this means you may be tuning some strings to 
flats instead of natural notes. If you have levers on the B strings, for example, you should tune those 
strings to B-flat when the lever is flipped down. You will then flip levers up when playing in the key 
of C.

Note that the tuning pins drive themselves a little deeper as you turn them clockwise to tighten the 
strings. If you find that they go deeper than you want, you can turn them counter-clockwise to raise 
the square ends back to a normal level. When you change strings in the future, you should turn these 
pins 3-4 complete revolutions counter-clockwise before installing the new strings.

BUZZING STRINGS -- 

Your harp need not suffer the problem of rattling or buzzing sounds when you 

play. If you hear such noises, you can correct them. Here are some troubleshooting hints:

If the buzzing sound occurs only when the sharping lever is flipped up (engaged), and you have 
Universal Levers, you need to screw the small brass bridge pins a little deeper into the wood. This 
lowers the string height so the strings make more firm contact with the sharping lever.

If the buzzing occurs  when the lever is flipped down (disengaged), the string may be vibrating against 
some part of the sharping lever. If you have Loveland brand levers, look very closely at the position 
of the string as it passes through the lever bracket. It may be rattling against the plastic cam (the part 
that you flip up and down), or against the small “fretpost” (the part that the cam pinches the string 
against when engaged.) You can change the position of the string by raising or lowering the brass 
bridge pin on which the string rests above the sharping lever. (Make sure the string is resting in the 
groove of that pin.) Use the small (5/64”) Allen wrench provided to turn the bridge pin in or out, 
watching how that moves the string in relation to the sharping lever.
 
If the problem is not located around the sharping lever, you may have a loose end of string that is 
rattling inside the soundchamber. Put your hand inside the harp and touch the knotted ends while 
plucking the harp to see where the problem is located. Oftentimes you can solve it by simply trimming 
off a loose end of string or by twisting the knotted end in a different direction.

Occasionally we hear of a buzz caused by a loose piece of wood, such as a decorative rosette or inlay 
strip. Test these things by pressing on the part while you pluck the string to see if the noise stops. 
When you find the loose part, you’ll need to add some glue to hold it firmly in place.

HARP REPAIRS -- 

If you ever need to repair the wood parts of your harp, you will be glad to know 

that the neck/pillar assembly can be taken apart and removed from the soundchamber to facilitate 
repair work. Simply loosen the strings and unhook them from the tuning pins. Then remove the 
screw at the base of the harp to allow the neck/pillar to come free of the harp body.

SCRATCHES & DENTS -- 

 You can restore the luster to the finish of your harp with a furniture polish 

like Old English with lemon oil. This will help hide scratches too. We avoid using polishes with wax 
because the wax will interfere with future refinishing or touch-up work.

HUMIDITY -- 

All acoustic instruments are susceptible to humidity. Moisture in the air can make the 

wood of an instrument shrink and swell. Over time, the shrinking and swelling can cause the wood 
to crack. The general rule for keeping an instrument from cracking is: If the weather is comfortable 
for a person, then it’s also comfortable for wood.

Содержание BALLAD HARP KIT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды