manualshive.com logo in svg

Musicmakers BALLAD HARP KIT, Руководство по сборке

Поделиться
Скачать
Musicmakers BALLAD HARP KIT Скачать руководство пользователя страница 25

651-439-9120

25 

www.harpkit.com

____55. Orient the feet on the bottom of the harp with 

the larger portion of the foot in the front. The 
feet should be nearly flush with the sides of 
the body of the harp. (fig. 55a)

Using an awl, mark where your screws will be 
located. Bore pilot holes into the base using a 
7/64” drill bit. Attach the feet using the 1-5/8” 
wood screws that are provided.

____56. Install a rubber bumper under each end of each foot, being careful with placement. Make sure 

that the rubber at the back end of the feet will stay in contact with the floor when you tip the 
harp back on your shoulder to play. 

Mark the placement with an awl. The pilot hole should be 3/4” away from the outside edge of 
the pad of the foot. (fig. 56a) Use a 7/64” bit to drill a pilot hole. Use a piece of tape to mark the 
depth of 1/2” on the drill bit. (fig. 56b)

FIG. 55A

Drill pilot holes 

with 7/64” drill bit.

Attach with 1-5/8” 

screws

NOTE:

  

Be very careful not to drill through the top side of the foot when you are drilling 

the pilot hole as well installing the screw. 

p

FIG. 56A, B

3/4”

7/64” Bit

1/2” Deep

____57. Use the 3/4” long round head screws provided, and attach the bumpers to the feet. (fig. 57a) 

Sometimes after the bumpers are installed, the harp doesn’t sit quite level. You can use washers 
to help shim up the bumper giving you trouble. (fig. 57b)

FIG. 57A, B

Содержание BALLAD HARP KIT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды