Multitech MTCBA-C-IP-N1 Скачать руководство пользователя страница 16

Страница: 16 / 202

Chapter 3 – General Commands

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J)

Phone Offline +CPOF

Description:

This command sends all CDMA software stack tasks offline. AT command can still be received, however,
there is no RF functionality. The AT+CFUN=0 command is equivalent to +CPOF.

Syntax:

Command syntax: AT+CPOF

Command

Possible Responses

AT+CPOF

Note: Stop CDMA stack

+CPOF:

OK Note: Command valid

Set Phone Functionality +CFUN

Description:

This command selects the mobile station’s level of functionality. AT+CFUN=0 is equivalent to AT+CPOF

The AT+CFUN=1 (by default, AT+CFUN will act the same as AT+CFUN=1) command restarts the entire
CDMA stack and CDMA functionality:

a complete software reset is performed

. In addition, the OK

response will be sent at the last baud rate defined by the +IPR command.

Values: <functionality

level>

Set the phone to OFFLINE mode.

Set the phone to ONLINE mode and resets.

Syntax:

Command syntax: AT+CFUN=<functionality level>

Command

Possible Responses

AT+CFUN?

Note: Ask for current functionality level

+CFUN: 1

OK
Note: Full functionality

AT+CFUN=0
Note: Set phone offline

OK
Note: Command valid

AT+CFUN=1
Note: Set phone ONLINE. A software reset is performed.

OK
Note: Command valid

Phone Activity Status +CPAS

Description:

This command returns the activity status of the mobile equipment.

Values:

<pas>

ready (allow commands from TA/TE)

unavailable (does not allow commands)

unknown

ringing (ringer is active)

call in progress

asleep (low functionality)

corrupted RF calibration values (checksum mismatch)

Syntax:

Command syntax: AT+CPAS

Command

Possible Responses

AT+CPAS

Note: Current activity status

+CPAS: <pas>

Report Mobile Equipment Errors +CMEE

Description:

This command disables or enables the use of the “+CME ERROR : <xxx>” or “+CMS ERROR :<xxx>” result
code instead of simply “ERROR”. See Chapter 20 "

MS Error Result Codes"

for +CME ERROR result codes

description and Chapter 20

"Message Service Failure Result Codes"

for +CMS ERROR result codes.

Syntax:

Command syntax: AT+CMEE=<error reporting flag>

Command

Possible Responses

AT+CMEE=0

Note: Disable MS error reports, use only « ERROR »

AT+CMEE=1

Note: Enable «+CME ERROR: <xxx>» or «+CMS ERROR: <xxx>»

Содержание MTCBA-C-IP-N1











































































































































































































Результаты поиска

Содержание MTCBA-C-IP-N1

Отзывы:

Multitech MTCBA-C-IP-N1, Справочное руководство, Страница: 16 / 202

Результаты поиска

Содержание MTCBA-C-IP-N1

Отзывы: