Multitech MTCBA-C-IP-N1 Скачать руководство пользователя страница 148

Страница: 148 / 202

Chapter 20 – Reference Information

Multi-Tech Systems, Inc. CDMA Wireless AT Commands (PN S000294J)

148

Message Service Failure Result Code: +CMS ERROR: <err>

<error>

Meaning

Resulting from the Following Commands

55-147

Reserved

148

Unsupported serial port baud rate

+WPPP

149

Socket transmit timeout

+WSTX

150-239

Reserved

240

FDN is active and number is not in FDN

+CMGS, +CMSS

241-301

Reserved

302

Operation not allowed

All SMS commands (+CMSS, +CMGL, +CPMS…

303

Reserved

304

Invalid mode parameter

+CMGS, +CMGW

305

Invalid text mode parameter

+CMGS, +CMGW, +CMSS

306-320

Reserved

321

Invalid memory index

+CMGR, +CMSS, +CMGD

322-339

Reserved

340

No +CNMA acknowledgement expected

+CNMA

341

Non Volatile Memory failure

All SMS commands

342-499 Reserved

Specific Error Result Codes

<error>

Meaning

Resulting from the Following Commands

500

unknown error.

All commands

501-512

Reserved

513

Lower layer failure (for SMS)

+CMGS, +CMSS (+CMS ERROR: 513)

514

Reserved

515

Please wait. Initialization or command processing in
progress.

Phonebook Initialization

516-518

Reserved

519

Reset the product to activate or change a new echo
cancellation.

+ECHO, +VIP

520-530 Reserved

531

Only FDN phonebook entries can be sent when the
FD facility is enabled.

+CMGS, +CMSS

532-599 Reserved

Extended Error Report (+CEER) Call Processing Codes

Cause Value

Diagnostic

No error detected in call processing

No CDMA service detected

Modem is in a call, operation not allowed

Modem is not in a call, operation not allowed

Modem is in an unknown call state

Call Barring is ON

Invalid or Not allowed CDMA Service Option

Invalid Parameter

Operation only allowed during an incoming call

Invalid Mode Selection

Invalid Roam Selection

Invalid Band Selection

Содержание MTCBA-C-IP-N1











































































































































































































Результаты поиска

Содержание MTCBA-C-IP-N1

Отзывы:

Multitech MTCBA-C-IP-N1, Справочное руководство, Страница: 148 / 202

Результаты поиска

Содержание MTCBA-C-IP-N1

Отзывы: