MTU 20V4000Bx4 Скачать руководство пользователя страница 207 | Manualshive

Страница: 207 / 304

background image

Replacing rings, installing injec-
tor

Note:

Remove plugs on HP line only before installa-
tion of the adapter.

1.

Remove plug.

2.

Use milling cutter to remove oil carbon from
sealing face on cylinder head and protective
sleeve.

Note:

• Replace sealing ring (1) between injector

and water sleeve whenever the injector is
disassembled.

• Make sure the ring assembly is correctly

positioned: The closed side of the CE ring
must abut on the injector, while the pro-
truding (open) side of the CE ring must
face the combustion chamber.

• A multi-purpose grease without solids

must be used.

3.

Install new sealing ring (1) abutted to (Multi-
purpose grease) and ensure that the installa-
tion position is correct.

4.

Fit damper ring (2) on injector and apply (As-
sembly compound (Molykote P 37)).

5.

Fit new O-rings (5) on injector (3) and apply
(Assembly compound (Kluthe Hakuform
30-15)).

Note:

Make sure that the sealing ring (4) does not
fall into the coolant sleeve.

6.

Ensure that the sealing ring (4) is correctly
seated.

7.

Insert injector (1) in the cylinder head, ensur-
ing that it is correctly aligned with the HP line
connection.

MS15039/01E 2018-11

| Injector | 205

TIM-ID: 0000081752 - 002

«
...
205
206
207
208
209
...
»

Содержание 20V4000Bx4

















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 20V4000Bx4

Бренд: Jabiru Страницы: 201

Бренд: Jabiru Страницы: 103

Бренд: Canaline Engines Страницы: 39

Бренд: Man Страницы: 64

Бренд: Polini Страницы: 34

Бренд: Shindaiwa Страницы: 48

Бренд: Wood-mizer Страницы: 36

EQP III 300 Series

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 6

Бренд: Toshiba Страницы: 31

EQP Global IEC Series

Бренд: Toshiba Страницы: 34

Бренд: Toshiba Страницы: 286

Бренд: Becker Страницы: 24

Бренд: Electric Drive Engineering Страницы: 19

Бренд: Yanmar Страницы: 142

Бренд: Robin America Страницы: 78

Бренд: Yanmar Страницы: 224

TWINMOT T2-PLUS H

Бренд: Germany Motions Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды