manualshive.com logo in svg

MTU 20V4000Bx4, Руководство по эксплуатации

Поделиться
Скачать
MTU 20V4000Bx4 Скачать руководство пользователя страница 153

7 Troubleshooting

7.1 Troubleshooting

Engine does not turn when starter is actuated

Cause

Corrective action

Battery low or faulty

u

Charge or replace (→ manufacturer's documentation).

Cable connections faulty

u

Check cable connections for secure seating (→ manufacturer's
documentation).

Starter (electric): Engine cabling
or starter faulty

u

Check whether cable connections are properly secured.
Contact Service.

Starter (compressed air): Cabling
on starting valve or starter
defective

u

Check whether cable connections are properly secured.
Contact Service.

Engine wiring faulty

u

Check (→ Page 282).

Engine / generator control:
Assemblies or connectors
possibly loose

u

Perform visual inspection (→ manufacturer's documentation).

Engine governor: Plug-in
connections loose

u

Check plug-in connections (→ Page 284).

Running gear blocked (engine
cannot be barred manually)

u

Contact Service.

Engine turns on starting but does not fire

Cause

Corrective action

Poor rotation by (electric) starter:
Battery low or faulty

u

Charge or replace (→ manufacturer's documentation).

Poor rotation by (air) starter:
Pressure too low.

u

Check compressed air system.

Engine wiring faulty

u

Check (→ Page 282).

Air in fuel system

u

Vent fuel system (→ Page 208).

Engine governor defective

u

Contact Service.

Engine fires unevenly

Cause

Corrective action

Injector defective

u

Check, replace as necessary (→ Page 196).

Engine wiring faulty

u

Check (→ Page 282).

Air in fuel system

u

Vent fuel system (→ Page 208).

Engine governor defective

u

Contact Service.

MS15039/01E 2018-11

| Troubleshooting | 151

TIM-ID: 0000074300 - 001

Содержание 20V4000Bx4

















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды