MR VACUTAP VR-Ex Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 256

background image

1 Introduction

Maschinenfabrik Reinhausen GmbH 2020

8

7545652/00 EN

VACUTAP

®

VR-Ex

1.4.1.1 Warning relating to section

Warnings relating to sections refer to entire chapters or sections, sub-sec-
tions or several paragraphs within this technical file. Warnings relating to
sections use the following format:

WARNING

Type of danger!

Source of the danger and outcome.

► Action

► Action

1.4.1.2 Embedded warning information

Embedded warnings refer to a particular part within a section. These warn-
ings apply to smaller units of information than the warnings relating to sec-
tions. Embedded warnings use the following format:

DANGER!

Instruction for avoiding a dangerous situation.

1.4.1.3 Signal words and pictograms

The following signal words are used:

Signal word

Definition

DANGER

Indicates a hazardous situation which, if not avoided, will result in
death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result
in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury.

NOTICE

Indicates measures to be taken to prevent damage to property.

Table 1: Signal words in warning notices

Pictograms warn of dangers:

Pictogram

Definition

Warning of a danger point

Warning of dangerous electrical voltage

«
...
6
7
8
9
10
...
»

Содержание VACUTAP VR-Ex

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR-Ex

Бренд: Jafar Страницы: 9

Бренд: Baileigh Industrial Страницы: 40

Бренд: IBASE Technology Страницы: 67

Бренд: IBC Страницы: 8

Бренд: IAI Страницы: 5

Бренд: Xycom Страницы: 65

Бренд: Zimmer Страницы: 16

Бренд: Zimmer Страницы: 2

Бренд: Igema Страницы: 22

ANT130LZ Series

Бренд: Aerotech Страницы: 52

EROX plus Penstock

Бренд: Vag Страницы: 11

Бренд: Danfoss Страницы: 33

Бренд: Ammeraal Beltech Страницы: 2

Бренд: Valmet Страницы: 49

Бренд: Kärcher Страницы: 424

Бренд: Chicago Pneumatic Страницы: 84

Бренд: Zimmer Страницы: 12

Бренд: Ravas Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды