MR VACUTAP VR-Ex Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 256

background image

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

137

7545652/00 EN

VACUTAP

®

VR-Ex

5.4.3 Performing transformer ratio test before drying

NOTICE

Damage to the on-load tap-changer!

Damage to the on-load tap-changer due to transformer ratio test being in-
correctly performed.

► Do not perform more than 250 tap-change operations on the on-load tap-

changer. If more than 250 tap-change operations are to be performed,
completely fill the oil compartment with insulating fluid and lubricate slid-
ing surfaces of contacts on the selector and selector gear with insulating
fluid.

► Only switch the on-load tap-changer from one operating position to the

next via the upper gear unit. You can use a short tube (diameter 25 mm)
with screwed-in coupling bolt (diameter 12 mm) with a hand wheel or
crank for this, for example. When using a drill, do not exceed a maximum
speed of 250 rpm.

► Always check the operating position reached through the inspection win-

dow in the on-load tap-changer head cover. Never overshoot the end po-
sitions, which are indicated in the connection diagram supplied with the
delivery.

► For multiple-column applications with a shared drive, link all on-load tap-

changer heads to one another using the horizontal drive shaft parts.

When actuating the change-over selector, a higher torque is required.

1. Switch the on-load tap-changer into the desired operating position. The di-

verter switch operation can be heard distinctly.

2.

NOTICE!

An incomplete tap-change operation may damage the on-load

tap-changer. After operating the diverter switch, continue to crank the
drive shaft of the upper gear unit for 2.5 revolutions in the same direction
in order to correctly complete the tap-change operation.

3. Perform the transformer ratio test.

4. Repeat the transformer ratio test in all operating positions.

5. Switch the on-load tap-changer into adjustment position (see the accom-

panying connection diagram for the on-load tap-changer).

After the transformer ratio test, open the kerosene drain plug in the oil com-
partment if the on-load tap-changer is to be dried with kerosene in the trans-
former tank. After drying, the diverter switch insert must be removed, the
kerosene drain plug in the oil compartment closed and the diverter switch
insert refitted.

«
...
135
136
137
138
139
...
»

Содержание VACUTAP VR-Ex

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR-Ex

Бренд: Grundfos Страницы: 43

IQAN-LC5-C0 Series

Бренд: Parker Страницы: 40

Бренд: Perun Airsoft Страницы: 8

Бренд: 6K Products Страницы: 17

Бренд: BOCK Страницы: 38

Бренд: National Instruments Страницы: 9

Бренд: Grizzly Страницы: 44

Бренд: Micromeritics Страницы: 62

Бренд: ZKTeco Страницы: 6

Бренд: Samoa Страницы: 28

Ford F-150 K9 Kennel

Бренд: D&R ELECTRONICS Страницы: 10

GQM22M5C2H620JB01 Series

Бренд: Murata Страницы: 25

ITA-5512 Series

Бренд: Advantech Страницы: 3

Бренд: Advantech Страницы: 38

Бренд: Vestil Страницы: 10

Бренд: EINHELL Страницы: 62

Hinds-Bock SP-64B

Бренд: Middleby Страницы: 15

HexGen HEX500-350HL

Бренд: Aerotech Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды