MR VACUTAP VR-Ex Скачать руководство пользователя страница 215 | Manualshive

Страница: 215 / 256

background image

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

215

7545652/00 EN

VACUTAP

®

VR-Ex

6.2 Transporting transformer to the operating site

NOTICE

Damage to motor-drive unit!

Damage to the motor-drive unit due to condensate in protective housing of
motor-drive unit.

► Always keep protective housing of the motor-drive unit tightly closed.

► In the event of downtime lasting more than 8 weeks prior to initial com-

missioning, connect and operate the anti-condensation heater in the mo-
tor-drive unit. If this is not possible, place a sufficient amount of desiccant
in the protective housing.

6.2.1 Transport with drive removed

1. Ensure that the drive and the on-load tap-changer are in the adjustment

position.

2. Remove the drive.

3. Do not actuate the drive while the on-load tap-changer is uncoupled and

do not turn the output shaft.

4. Do not actuate an on-load tap-changer which is uncoupled and do not turn

its drive shaft.

5. Transport the drive to the installation site in the MR delivery packaging.

6. Fit the drive [

Section 5.5.3, Page 185] and the drive shaft to the trans-

former at the installation site.

6.2.2 Transport with full transformer tank and without oil conservator

Attach a connecting lead between the on-load tap-changer's oil compartment
and the transformer tank if the transformer has been transported with a full
tank and without an oil conservator.

► Establish a connecting lead on the on-load tap-changer head between

connections E2 and Q or E2 and R.

Figure 249: Connecting lead

«
...
213
214
215
216
217
...
»

Содержание VACUTAP VR-Ex

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR-Ex

Бренд: T-Drill Страницы: 75

Бренд: e-survey Страницы: 54

Бренд: Frick Страницы: 36

Бренд: Sammode Страницы: 12

Бренд: INNOSILICON Страницы: 12

Бренд: R.V.R. Elettronica Страницы: 72

SUNSUN Skimmer CSP-40

Бренд: WilTec Страницы: 8

DigiConvert MC004-2014 P1082

Бренд: Markem Imaje Страницы: 79

Бренд: DENTSPLY Страницы: 211

Бренд: Moxa Technologies Страницы: 2

XP-504-10-A10-A01-2B

Бренд: Eaton Страницы: 134

Бренд: Zimmer Страницы: 44

Бренд: ITOH DENKI Страницы: 39

Бренд: Baileigh Industrial Страницы: 40

RA 240 D2x3 IE2

Бренд: Ringler Страницы: 56

Бренд: Belmash Страницы: 80

V Box Express II

Бренд: Kontron Embedded Computers Страницы: 46

Part Feeding 7.0

Бренд: Epson Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды