MR VACUTAP VR-Ex Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 256

background image

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

140

7545652/00 EN

VACUTAP

®

VR-Ex

3. Remove on-load tap-changer head cover.

Figure 144: On-load tap-changer head cover

5.4.5.1.3 Drying the on-load tap-changer

NOTICE

Damage to the on-load tap-changer head cover and on-load tap-
changer accessories.

Both the on-load tap-changer head cover and the on-load tap-changer ac-
cessories will become damaged if they are dried.

► Never dry the on-load tap-changer head cover or the following acces-

sories: motor-drive unit, drive shaft, protective relay, pressure monitoring
device, pressure relief device, bevel gear, temperature sensor, oil filter
unit.

1. Heat up the on-load tap-changer in air at atmospheric pressure with a

temperature increase of approximately 10 °C/h to a final temperature of
maximum 110 °C.

2. Pre-dry the on-load tap-changer in circulating air at a maximum tempera-

ture of 110 °C for a period of at least 20 hours.

3. Vacuum-dry on-load tap-changer at between 105 °C and maximum

125 °C for at least 50 hours.

4. Residual pressure of no more than 10

-3

bar.

5.4.5.1.4 Securing on-load tap-changer head cover

NOTICE

Damage to the on-load tap-changer!

A missing or damaged o-ring as well as unclean sealing surfaces lead to in-
sulating fluid escaping and therefore to damage to the on-load tap-changer.

► Ensure that the o-ring is positioned untwisted in the on-load tap-changer

head cover.

► Ensure that the o-ring does not become damaged when mounting the

cover.

► Ensure that the sealing surfaces on the on-load tap-changer head cover

and on-load tap-changer head are clean.

«
...
138
139
140
141
142
...
»

Содержание VACUTAP VR-Ex

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR-Ex

Бренд: Igema Страницы: 22

Бренд: CDVI Страницы: 2

Бренд: Cooper Страницы: 20

Бренд: LEAB Страницы: 8

Бренд: Swienty Страницы: 31

Бренд: SAMCHULLY Страницы: 44

Бренд: Wilo Страницы: 24

Бренд: PI Страницы: 42

Бренд: Clark-Reliance Страницы: 8

Бренд: Hydrofarm Страницы: 4

Бренд: ABB Страницы: 13

Бренд: jbc Страницы: 4

Бренд: Tyco Electronics Страницы: 38

Бренд: GSi Страницы: 24

Бренд: Fueltec Страницы: 13

Sub Mounting Kit

Бренд: Viessmann Страницы: 16

Бренд: XtraVac Страницы: 18

Бренд: J&D MAnufacturing Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды