MR VACUTAP VR-Ex Скачать руководство пользователя страница 226

Страница: 226 / 256

7 Fault elimination

Maschinenfabrik Reinhausen GmbH 2020

226

7545652/00 EN

VACUTAP

VR-Ex

7.1.2 Flap valve in OFF position

If the flap valve is in the OFF position, proceed as follows:

1. Ensure that the transformer is not started up under any circumstances.

2. Contact and inform Maschinenfabrik Reinhausen of the following:

Serial number of protective relay and on-load tap-changer

What was the load of the transformer at the instant of tripping?

Was the on-load tap-changer moved immediately before or during trip-
ping?

Did any other protective devices of the transformer respond at the in-
stant of tripping?

Were switching operations in the network being carried out at the in-
stant of tripping?

Were overvoltages registered at the instant of tripping?

3. Take further action in agreement with Maschinenfabrik Reinhausen.

7.1.3 Re-commissioning the transformer

Once the reason for the protective relay tripping has been established and
remedied, you can re-commission the transformer:

1. Check the protective relay.

2. Commission the transformer.

Содержание VACUTAP VR-Ex

































































































































































































































































Результаты поиска

Содержание VACUTAP VR-Ex

Отзывы:

Похожие инструкции для VACUTAP VR-Ex

Бренды по названию

Популярные бренды

MR VACUTAP VR-Ex, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание VACUTAP VR-Ex

Отзывы:

Похожие инструкции для VACUTAP VR-Ex

Бренды по названию

Популярные бренды