MR VACUTAP VM-Ex Скачать руководство пользователя страница 124

Страница: 124 / 210

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

124

5293079/01 EN

VACUTAP

VM-Ex

5.4.8.2.1 Removing diverter switch insert

5.4.8.2.1.1 Moving on-load tap-changer to adjustment position

► Move the on-load tap-changer to the adjustment position. The adjustment

position is indicated in the on-load tap-changer connection diagram in-
cluded in delivery.

5.4.8.2.1.2 Removing on-load tap-changer head cover

WARNING

Danger of explosion!

Danger of death from explosive gases under the on-load tap-changer head
cover!

► Ensure that there are no open flames, hot surfaces or sparks (for exam-

ple caused by static charging) in the immediate surroundings and that
none arise.

► De-energize all auxiliary circuits (for example tap-change supervisory de-

vice) before removing the on-load tap-changer head cover.

► Do not operate any electrical devices during the work (for example risk of

sparks caused by impact wrench).

► Only use conductive and grounded hoses, pipes, and pump equipment

that are approved for flammable liquids.

NOTICE

Damage to the on-load tap-changer!

Small parts in the oil compartment may block the diverter switch insert,
thereby damaging the on-load tap-changer.

► Ensure that parts do not fall into the oil compartment.

► Check that all small parts are accounted for.

1. Make sure that inspection window is sealed off with cover.

2. Loosen screws with locking elements on on-load tap-changer head cover.

Figure 134: On-load tap-changer head cover

Содержание VACUTAP VM-Ex



















































































































































































































Результаты поиска

Содержание VACUTAP VM-Ex

Отзывы:

Похожие инструкции для VACUTAP VM-Ex

Бренды по названию

Популярные бренды

MR VACUTAP VM-Ex, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание VACUTAP VM-Ex

Отзывы:

Похожие инструкции для VACUTAP VM-Ex

Бренды по названию

Популярные бренды