MR VACUTAP VM-Ex Скачать руководство пользователя страница 103

Страница: 103 / 210

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

103

5293079/01 EN

VACUTAP

VM-Ex

2. Increase the kerosene vapor temperature by approx. 10°C/hour to the de-

sired final temperature of max. 125°C at the on-load tap-changer.

3. Vacuum-dry on-load tap-changer at between 105°C and maximum 125°C

for at least 50 hours.

4. Residual pressure of no more than 10

-3

bar.

►

NOTICE!

Close kerosene drain plug clockwise (tightening torque 20 Nm).

An open kerosene drain plug leads to oil escaping from the oil compart-
ment and therefore to damage to the on-load tap-changer and trans-
former.

5.4.6 Lifting top part of on-load tap-changer head off supporting

flange (bottom part)

5.4.6.1 Removing on-load tap-changer head cover

WARNING

Danger of explosion!

Danger of death from explosive gases under the on-load tap-changer head
cover!

► Ensure that there are no open flames, hot surfaces or sparks (for exam-

ple caused by static charging) in the immediate surroundings and that
none arise.

► De-energize all auxiliary circuits (for example tap-change supervisory de-

vice) before removing the on-load tap-changer head cover.

► Do not operate any electrical devices during the work (for example risk of

sparks caused by impact wrench).

► Only use conductive and grounded hoses, pipes, and pump equipment

that are approved for flammable liquids.

NOTICE

Damage to the on-load tap-changer!

Small parts in the oil compartment may block the diverter switch insert,
thereby damaging the on-load tap-changer.

► Ensure that parts do not fall into the oil compartment.

► Check that all small parts are accounted for.

1. Make sure that inspection window is sealed off with cover.

Содержание VACUTAP VM-Ex



















































































































































































































Результаты поиска

Содержание VACUTAP VM-Ex

Отзывы:

Похожие инструкции для VACUTAP VM-Ex

Бренды по названию

Популярные бренды

MR VACUTAP VM-Ex, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание VACUTAP VM-Ex

Отзывы:

Похожие инструкции для VACUTAP VM-Ex

Бренды по названию

Популярные бренды