background image

MD-119 Hardware Manual 

The software described in this manual is furnished under a license agreement and may be used only in accordance with 

the terms of that agreement. 

Copyright Notice 

© 2013 Moxa Inc. All rights reserved. 

Trademarks 

The MOXA logo is a registered trademark of Moxa Inc. 

All other trademarks or registered marks in this manual belong to their respective manufacturers. 

Disclaimer 

Information in this document is subject to change without notice and does not represent a commitment on the part of 
Moxa. 
 
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited 
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the 
products and/or the programs described in this manual, at any time. 
 
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for 
its use, or for any infringements on the rights of third parties that may result from its use. 
 
This product might include unintentional technical or typographical errors. Changes are periodically made to the 
information herein to correct such errors, and these changes are incorporated into new editions of the publication. 

Technical Support Contact Information 

www.moxa.com/support 

Moxa Americas

   

Toll-free:  1-888-669-2872 
Tel:   

+1-714-528-6777 

Fax:  

+1-714-528-6778

 

 

Moxa China (Shanghai office)

   

Toll-free:  800-820-5036 
Tel:   

+86-21-5258-9955 

Fax:  

+86-21-5258-5505

 

Moxa Europe

   

Tel:   

+49-89-3 70 03 99-0 

Fax:  

+49-89-3 70 03 99-99

 

 

Moxa Asia-Pacific

   

Tel:   

+886-2-8919-1230 

Fax:  

+886-2-8919-1231

 

 

Содержание MD-119













































Отзывы: