Moxa Technologies MD-119 Скачать руководство пользователя страница 3

Страница: 3 / 44

Table of Contents

Introduction ...................................................................................................................................... 1-1

Overview ........................................................................................................................................... 1-2

Package Checklist ............................................................................................................................... 1-2

Product Features ................................................................................................................................ 1-2

MD-119 Hardware Specifications .......................................................................................................... 1-3

Hardware Introduction...................................................................................................................... 2-1

Appearance and Layout ....................................................................................................................... 2-2

Dimensions ........................................................................................................................................ 2-3

LED Indicators .................................................................................................................................... 2-3

On-screen Display Control Buttons ........................................................................................................ 2-3

Hardware Installation and Peripherals .............................................................................................. 3-1

Installing the MD-119 .......................................................................................................................... 3-2

Wiring Requirements ........................................................................................................................... 3-2

Connecting Power Sources ................................................................................................................... 3-3

Grounding the MD-119 ........................................................................................................................ 3-3

Connecting Data Transmission Cables ................................................................................................... 3-3

Connecting to a Serial Device ....................................................................................................... 3-3

Connecting to Computers or Laptops ..................................................................................................... 3-4

Enabling the Built-in Buzzer ................................................................................................................. 3-5

Regulatory Approval Statement ........................................................................................................ A-1

On-screen Display and Display Configuration .................................................................................... B-1

On-screen Display (OSD) Controls ........................................................................................................ B-2

Opening the Configuration Screen ................................................................................................. B-2

OSD Passwords/Keycode ..................................................................................................................... B-2

OSD Filetree Legend ........................................................................................................................... B-3

OSD Menu Map ................................................................................................................................... B-3

Main Group 1 .............................................................................................................................. B-4

Main Group 2 .............................................................................................................................. B-5

Main Group 3 .............................................................................................................................. B-6

OSD Menu Items Explained .................................................................................................................. B-7

Basic Image Properties ................................................................................................................ B-7

Picture: PIP Adjustments .............................................................................................................. B-8

Picture: Advanced Settings ........................................................................................................... B-9

Swap Input Sources: Main to Second / Second to Main .................................................................. B-11

Image Information .................................................................................................................... B-12

Auto-Setup ............................................................................................................................... B-12

Display Setup: OSD ................................................................................................................... B-12

Display Setup: User Settings ...................................................................................................... B-14

Display Setup: Preset Defaults .................................................................................................... B-15

Display Setup: Service Menu ...................................................................................................... B-16

Display: Input Sources / Dual Image Displays ............................................................................... B-16

Power Off ................................................................................................................................. B-18

Display UART Command .................................................................................................................... C-1

Connecting to the Display .................................................................................................................... C-2

UART Software Configuration ............................................................................................................... C-2

Date Rate ................................................................................................................................... C-2

Data Format ............................................................................................................................... C-2

UART Command Format ...................................................................................................................... C-2

Command Format Description ....................................................................................................... C-2

Downloading Files ............................................................................................................................... C-4

Downloading Files ....................................................................................................................... C-4

Downloading Dual RGB File ........................................................................................................... C-5

Uploading/Downloading Configuration Files ..................................................................................... C-5

OSD Control Command ........................................................................................................................ C-6

BLI (Brightness Control) ............................................................................................................... C-6

DST (Display State) ..................................................................................................................... C-6

MAN (Manufacturer ID Code) ........................................................................................................ C-6

POT (Potentiometer Control) ......................................................................................................... C-7

SNB (Serial Number Query) .......................................................................................................... C-7

TYP (Type/Model/Number Query) .................................................................................................. C-7

SWI (Software Version Query) ...................................................................................................... C-8

VER (Version Number) ................................................................................................................. C-8

MCC (OSD Control) ...................................................................................................................... C-8

MCC Control Command ........................................................................................................................ C-9

Содержание MD-119












































Результаты поиска

Содержание MD-119

Отзывы:

Похожие инструкции для MD-119

Бренды по названию

Популярные бренды

Moxa Technologies MD-119, Руководство по оборудованию

Результаты поиска

Содержание MD-119

Отзывы:

Похожие инструкции для MD-119

Бренды по названию

Популярные бренды