MOTO GUZZI California 1400 Скачать руководство пользователя страница 99

Страница: 99 / 411

CONNECTOR CHECK PROCEDURE

The procedure includes the following checks:

1. Observation and check of the connector correct

position on the component or on the coupling con-

nector, making sure that the locking catch is re-

leased.

2. Observation of the terminals on the connector:

no rust marks or dirt should be present and it is

important to check terminal correct positioning on

the connector (i.e., all terminals aligned at the

same depth) and terminal integrity (i.e., that termi-

nals are not loose, open/bent, etc.). For connec-

tors whose terminals are not visible (e.g. Marelli

control unit) use a metal cable of suitable diameter

and introduce it carefully in the connector slot at

the same depth as for the other terminals of the

connector.

CAUTION

IN CASE OF TEMPORAL MALFUNCTIONING, CARRY OUT
ALL DUE CHECKS LOOKING FOR FAULT BY MOVING
SLIGHTLY THE CABLE HARNESS BEING INSPECTED.

3. Pulling the cables slightly from the back of the connector in order to check the correct position of

terminals on the connector and of the cable on the terminal.

CONTINUITY check

Check goal:

this control is to check that there are not any circuit interruptions nor excessive resistance,

for instance caused by rust, on the two terminals being inspected.

Tester:

set the tester on the "continuity" symbol and place the tester probes on the two circuit ends:

the tester emits a sound signal only if there is continuity; the tester can also be set to the Ohm symbol

to check that the circuit resistance is null or a few tenths of an Ohm.

CAUTION: THE CIRCUIT SHOULD NOT BE ENERGISED, OTHERWISE THE TEST IS IRRELE-

VANT.

GROUND CONNECTION check

Check goal:

this control is to check if a cable or a circuit is in contact with the vehicle ground (-)

connection.

Tester: set the tester on the "continuity" symbol and place one tester probe on the vehicle ground

connection (or on the battery - terminal) and the other probe on the cable being inspected: the tester

sends out a sound signal only if there is continuity. The tester can also be set to the Ohm symbol to

check that the circuit resistance is null or a few tenths of an Ohm.

California 1400

Electrical system

ELE SYS - 99

Содержание California 1400




























































































































































































































































































































































































































Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI California 1400, Инструкция по эксплуатации

Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды