manualshive.com logo in svg

MOTO GUZZI California 1400, Инструкция по эксплуатации

Поделиться
Скачать
MOTO GUZZI California 1400 Скачать руководство пользователя страница 55

km x 1,000

1.5

10

20

30

40

50

60

70

80

Fuel lines (3)

I

I

I

I

I

I

I

I

Brake lines (3)

I

I

I

I

I

I

I

I

Brake pad wear (1)

I

I

I

I

I

I

I

I

I

Labour time (minutes)

140

220

200

220

200

230

200

220

200

Transmission fluid

Check

•

Remove the rear wheel.

•

Undo and remove the three fixing

screws (1) of the protection shield (2).

•

Remove the protection shield (2).

• Keep the vehicle upright with both wheels on the

ground.

• Unscrew and remove the cap/dipstick (4).

• The level is correct if the oil is close to the hole

of the cap/dipstick (4).

• If the oil is lower than specified, top-up until it

reaches the cap/dipstick hole (4).

CAUTION

DO NOT ADD ADDITIVES OR ANY OTHER SUBSTANCE TO
THE FLUID. WHEN USING A FUNNEL OR ANY OTHER EL-
EMENT, MAKE SURE IT IS PERFECTLY CLEAN.

See also

Removing the

rear wheel

Replacement

CAUTION

THE UNIT MUST BE HOT WHEN THE OIL IS CHANGED AS UNDER SUCH CONDITIONS OIL IS
FLUID AND THEREFORE EASY TO DRAIN.

NOTE

RIDE SOME km (miles) TO WARM UP ENGINE OIL

•

Place a container with an over 400 cm³ (25 cu.in) capacity under the drainage plug (5).

•

Unscrew and remove the drainage plug (5).

California 1400

Maintenance

MAIN - 55

Содержание California 1400




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды