MOTO GUZZI California 1400 Скачать руководство пользователя страница 345

Страница: 345 / 411

Riding with an active ABS system

•

At engine starter, the ABS warning light

(5) on the instrument panel (4) flashes

until the vehicle exceeds 5 km/h (3.1

mph).

If the ABS warning light remains on when the

vehicle is running, it means that a fault has

been detected and the ABS system has been

automatically deactivated.

Riding with a deactivated ABS system

The warning light (5) turns on permanently, the system was deactivated.

Guide to diagnosis

PREMISE

Each time the key is ON, if, at least one current or

stored* error is detected, the ABS warning light

turns on permanently.

The ABS system is deactivated automatically

The system operates perfectly just as any other

braking system without ABS

* The diagnosis requires exceeding the 5 km/h

(3.1 mph).

Each time the key is ON, if at least one current or stored* error of the ABS system is not detected:

•

the ABS warning light flashes.

When the 5 km/h (3.1 mph) are exceeded:

- if errors are not detected: the ABS warning light turns off

- if at least one malfunction is detected: the ABS warning light turns on permanently.

The ABS system is deactivated!

The system operates perfectly just as any other braking system without ABS.

The detection of malfunctions may require more or less time according to the type of failure.

Error detection logic foresees that for the errors to be diagnosed one or more conditions must persist

within a given time.

If during this given time one of the conditions is missing but then it comes back, the timer is reset and

the system is no longer able to diagnose the error.

The ABS system is still inactive.

Example:

California 1400

Braking system

BRAK SYS - 345

Содержание California 1400




























































































































































































































































































































































































































Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI California 1400, Инструкция по эксплуатации

Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды