MOTO GUZZI California 1400 Скачать руководство пользователя страница 308

Страница: 308 / 411

•

Tighten the piston fixing screws in the

fork end to the prescribed torque.

Filling oil

•

Place the sleeve upright in a vice fitted

with protection shoes.

•

Compress the sleeve in the stem.

Place a support under the stem in order

to leave it compressed.

•

Pour part of the fork oil into the sleeve.

•

Wait some minutes until the oil fills all

the ducts.

•

Pour the remaining oil.

•

Pump out oil a few times.

•

Measure the air gap between the oil

level and the rim.

THE SLEEVE MUST BE PERFECTLY UPRIGHT IN ORDER
TO MEASURE THE CORRECT OIL LEVEL. THE OIL LEVEL
MUST BE THE SAME IN BOTH STANCHIONS.

Specific tooling

020951Y

Stanchion support

Characteristic

Fork oil

Suspensions

California 1400

SUSP - 308

Содержание California 1400




























































































































































































































































































































































































































Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI California 1400, Инструкция по эксплуатации

Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды