MOTO GUZZI California 1400 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 411

MOTO GUZZI California 1400 Скачать руководство пользователя страница 8

•

Keep away from heat sources.

REASSEMBLING COMPONENTS

CAUTION

BEARINGS MUST ROTATE FREELY, WITHOUT JAMMING AND/OR NOISE, OTHERWISE, THEY
NEED TO BE REPLACED.

•

Only use ORIGINAL Aprilia SPARE PARTS.

•

Comply with lubricant and consumables use guidelines.

•

Lubricate parts (whenever possible) before reassembling them.

•

When tightening nuts and screws, start either from the components with the largest diameter

or from the innermost components, proceeding diagonally. Tighten nuts and screws in suc-

cessive steps before applying the tightening torque.

•

Always replace self-locking nuts, washers, sealing rings, circlips, O-rings (OR), cotter pins

and screws with new parts if the thread is damaged.

•

When assembling the bearings, make sure to lubricate them well.

•

Check that each component is assembled correctly.

•

After a repair or routine maintenance, carry out pre-ride checks and test the vehicle on

private grounds or in an area with low traffic.

•

Clean all mating surfaces, oil seal rims and gaskets before refitting. Smear a thin layer of

lithium-based grease on the oil seal rims. Reassemble oil seals and bearings with the brand

or batch number facing outward (visible side).

ELECTRICAL CONNECTORS

Electric connectors must be disconnected as described below; failure to comply with this procedure

causes irreparable damage to both the connector and the wiring harness:

Press the relative safety clips, if applicable.

•

Grip the two connectors and disconnect them by pulling them in opposite directions.

•

If any signs of dirt, rust, moisture, etc. are noted, clean the inside of the connector carefully

with a jet of compressed air.

•

Ensure that the cables are correctly fastened to the internal connector terminals.

•

Then connect the two connectors, ensuring that they couple correctly (if fitted with clips, you

will hear them "click" into place).

CAUTION

DO NOT DISCONNECT CONNECTORS BY PULLING THE CABLES.

NOTE

THE TWO CONNECTORS CAN ONLY BE CONNECTED IN ONE DIRECTION: CONNECT THEM
THE RIGHT WAY ROUND.

TIGHTENING TORQUES

CAUTION

REMEMBER THAT THE TIGHTENING TORQUES FOR ALL FASTENING ELEMENTS ON WHEELS,
BRAKES, WHEEL AXLES AND ANY OTHER SUSPENSION COMPONENTS PLAY A KEY ROLE
IN ENSURING VEHICLE SAFETY AND MUST COMPLY WITH SPECIFIED VALUES. CHECK THE
TIGHTENING TORQUES OF FASTENING ELEMENTS ON A REGULAR BASIS AND ALWAYS USE

Characteristics

California 1400

CHAR - 8

«
...
6
7
8
9
10
...
»

Содержание California 1400




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды