manualshive.com logo in svg

MOTO GUZZI California 1400, Инструкция по эксплуатации

Поделиться
Скачать
MOTO GUZZI California 1400 Скачать руководство пользователя страница 202

Checking the desmodromic drum

Check gear drum for damage, scratches and wear

and replace the desmodromic control rod if nec-

essary.

Check the desmodromic segment «

3

» for damage

and wear and replace it if necessary.

Check the desmodromic bearing «

4

» for damage

and cracks and replace it if necessary.

Checking the forks

NOTE

THE FOLLOWING PROCEDURE IS VALID FOR ALL GEARBOX FORKS.

•

Check the transmission fork cam roller

«1» and the transmission fork tooth

«2» for damage, deformation and

wear.

•

Replace the transmission fork if nec-

essary.

•

Check the transmission fork move-

ment and if it is not regular, replace the

transmission forks.

See also

Disassembling the gearbox

Fitting the primary shaft

NOTE

TO REFIT, FOLLOW THE SAME INSTRUCTIONS AS FOR REMOVAL BUT IN REVERSE ORDER.
REMEMBER TO REPLACE ALL SEALING RINGS, CIRCLIPS AND SAFETY RINGS PREVIOUSLY
REMOVED.

See also

Removing the

Engine

California 1400

ENG - 202

Содержание California 1400




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды