MOTO GUZZI California 1400 Скачать руководство пользователя страница 132

Страница: 132 / 411

•

shorted to positive

Error cause

•

Excessive voltage (battery voltage) has been detected at PIN 10 and 22 of the ENGINE

connector. Caution: the 'Oxygen sensor' parameter is not the real value that is read; a re-

covery value is displayed instead. The instrument panel does not indicate the presence of

this error even in the ATT status.

Troubleshooting

•

shorted to positive: with key set to ON, disconnect the sensor connector and measure PIN

1 voltage on the cable harness side (grey cable): if there is voltage (5 or 12 V), restore the

cable harness; if there is not, replace the oxygen sensor

'Heating left cylinder lambda probe P0135

•

short circuit to positive/ open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 32 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 32 of the ENGINE connector. The instrument panel does not indicate the presence

of this error even in the ATT status.

Troubleshooting

•

If shorted to positive: disconnect the probe connector and check the sensor correct resist-

ance: replace the sensor if not OK; if it is OK, restore the cable harness (Green/Red cable)

•

If circuit is open, shorted to negative: check circuit continuity from probe connector (PIN 3

and 4) toward the probe: if it is not OK, replace the probe; if it is OK, check the sensor

connector and the Marelli control unit connector: if it is not OK, restore; if it is OK, with key

set to ON and sensor connector disconnected, check if there is battery voltage at PIN 4: if

it is not OK, check the Red/Brown cable continuity between the probe connector and the

auxiliary injection relay (No. 28 in the wiring diagram, placed in the front relay box, left side;

CHECK, however, the identification of the relay with the colour of the cables). If there are

also coil, lower and upper injector and secondary air errors, check the relay and its excitation

and power line; if there is voltage at PIN 4, check the Green/Red cable ground insulation

(PIN 3): if not OK, restore the cable harness. If it is OK, check the continuity of the Green/

Red cable (between the sensor connector PIN 3 and the ENGINE PIN 32) and restore the

cable harness.

WARNING

The control unit does not detects the following malfunctions of the oxygen sensor circuit according to

the signal: interrupted circuit, shorted to ground or sensor malfunction (for example non variable volt-

age). In case of fault indication, carry out the following troubleshooting.

Troubleshooting

Electrical system

California 1400

ELE SYS - 132

Содержание California 1400




























































































































































































































































































































































































































Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI California 1400, Инструкция по эксплуатации

Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды