MOTO GUZZI California 1400 Скачать руководство пользователя страница 126

Страница: 126 / 411

•

According to the engine operation data (rpm, throttle, etc.) an average value for the intake

pressure is estimated: if the value read deviates by a given percentage, this error is activa-

ted. The most frequent causes can be: abnormal resistance in the sensor circuit (for

example, rusted terminals) or sensor with poor performance.

Troubleshooting

•

Check the Marelli control unit connector and the sensor connector; if not OK, restore. If

everything is OK, check that resistance between ENGINE connector PIN 24 and sensor

connector PIN 4 is a few tenths of an Ohm; If it is above that value, restore cable harness.

Replace the sensor if it is correct.

Error due to unexpected air intake in the manifold P0210

•

signal not valid.

Error cause

•

A small difference between the estimated pressure and the measured pressure has been

detected: the measured pressure is higher than the estimated one (intake manifold condi-

tions).

Troubleshooting

•

Check the conditions of the intake manifold and cleanliness of the hole for pressure reading.

Estimation error for cylinder intake manifold pressure P0215

•

too high pressure/too low pressure.

Error cause

•

A substantial difference between the estimated pressure and the measured pressure has

been detected (for example, the hole for pressure reading is clogged or sensor screw is

loose).

Troubleshooting

•

Check the conditions of the intake manifold and cleanliness of the hole for reading the pres-

sure: there is an evident defect in the intake and pressure reading systems.

Manifold pressure too low error P0217

•

signal not valid.

Error cause

•

A small difference between the estimated pressure and the measured pressure has been

detected: the measured pressure is below the estimated one (for example, smeared throttle

body).

Troubleshooting

•

Check the conditions of the intake manifold and cleanliness of the hole for pressure reading.

Electrical system

California 1400

ELE SYS - 126

Содержание California 1400




























































































































































































































































































































































































































Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI California 1400, Инструкция по эксплуатации

Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды