manualshive.com logo in svg

MOTO GUZZI California 1400, Инструкция по эксплуатации

Поделиться
Скачать
MOTO GUZZI California 1400 Скачать руководство пользователя страница 353

IT IS ADVISABLE TO CREATE A TEMPLATE

TO CHECK THE CORRECT CONNECTOR IN-

SERTION.

•

Fit the protection casing.

Component maintenance

The vehicle is fitted with a two-channel ABS sys-

tem, i.e. it works on both the front and the rear

wheel.

Check periodically and each time the wheels are

refitted, the tone wheel (2) or the sensor (1) re-

placed, that the wheel distance is constant at each

360°. Use a thickness gauge to check the distance

between sensor (1) and tone wheel (2) at three

points at a 120° span. The values should be be-

tween:

0.3 - 2.00 mm (0.012 - 0.079 in)

 for the front one;

0.3 - 2.00 mm (0.012 - 0.079 in)

 for the rear one;

CAUTION

IF A VALUE BEYOND THE TOLERANCE RANGE IS MEAS-
URED, REPLACE THE SENSOR (1) AND/OR THE TONE
WHEEL (2) AND REPEAT THE CHECKS; MAKE SURE
THAT THE VALUES ARE WITHIN THE TOLERANCE LIM-
ITS.

TONE WHEELS (2) CLEANING

It is important to check that all the tone wheels (2) are always clean. Otherwise,: gently remove any

possible dirt deposits with a cloth or metal brush. Avoid using solvents, abrasives and air or water jets

directly on the tone wheel (2).

TONE WHEEL SENSOR REPLACEMENT

Disconnect the tone wheel sensor connector (1) from the main wire. Unscrew and remove the screw

and remove the tone wheel sensor (1).

CAUTION

BEFORE REFITTING, MAKE SURE THAT THE FAYING SURFACES BETWEEN THE SENSOR (1)
AND THE SEAT ITSELF DO NOT SHOW SIGNS OF DAMAGE AND ARE COMPLETELY CLEAN.
ALWAYS CHECK THE DISTANCE BETWEEN THE SENSOR (1) AND THE TONE WHEEL (2).

California 1400

Braking system

BRAK SYS - 353

Содержание California 1400




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды