MOTO GUZZI California 1400 Скачать руководство пользователя страница 398

Страница: 398 / 411

the cable grommet in the right bracket

(11).

•

Using the upper bayonet mount, con-

nect the frame, complete with wind-

shield, to the fasteners (2) which have

just been assembled.

•

Secure the lower mounting bracket (5)

to the lower steering yoke using the two

screws (4).

•

Slightly widen the cable grommet (11)

and pass the accelerator cables

through as illustrated.

•

Slightly lubricate the rubber blocks (12)

and insert them into the frame pipes.

Battery

•

Unscrew and remove the four screws

in the figure.

•

Remove the battery cover.

Bodywork

California 1400

BODYW - 398

Содержание California 1400




























































































































































































































































































































































































































Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI California 1400, Инструкция по эксплуатации

Результаты поиска

Содержание California 1400

Отзывы:

Бренды по названию

Популярные бренды