Morgana AutoCreaser Pro 33A Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 54

background image

Quick Start Guide

Cross Perforating (Optional).

1. A cross perforating kit is available as an optional part, the blades available are:

Full Width - Course

Full Width - Fine
150mm - Course
150mm - Fine
100mm - Course
100mm - Fine
50mm - Course
50mm - Fine

Refer to page 38 for fitting of the perforator blade set.

2. Select the Perforating Button to turn on the Perforating, this mode slows down
the machine cycle to allow the ejectors on the perforation blade set release the
paper from the blade.

3. The procedure for setting the perforation positions from the lead edge is
identical to positioning creases on a sheet.

Page 14

CREASING

6. Enter the Hinge Dimension.

7. Select the arrow button to highlight the Spine Offset and the Spine Width
dimensions.

8. Run the sheets of paper through the machine to make the Spine creases.

TO MAKE THE HINGE CREASES.

9. Remove the sheets of paper from the stacker tray.

TURN THE SHEETS OVER

,

and put them back onto the loading table.

MAKE SURE THAT THE LEAD EDGE

OF THE SHEETS POINT IN THE SAME DIRECTION AS BEFORE.

10. Select the arrow button to highlight the Hinge Dimension.

11. Run the sheets of paper through the machine to make the Hinge creases.

Hinge Dimension

Quick Start Guide

Page 15

SYSTEM

Perforating Button

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

«
...
13
14
15
16
17
...
»

Содержание AutoCreaser Pro 33A























































Отзывы:

Нет отзывов

Похожие инструкции для AutoCreaser Pro 33A

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: Ecco Страницы: 3

Бренд: Samsung Страницы: 2

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

AquaPure Ei Series

Бренд: Jandy Страницы: 4

Бренд: janitza Страницы: 30

AquaPure Ei Series

Бренд: Jandy Страницы: 8

Jandy Pro Series

Бренд: Jandy Страницы: 16

Бренд: Vatech Страницы: 137

Бренд: Vatech Страницы: 68

Бренд: Varytec Страницы: 52

Бренд: Össur Страницы: 98

Flex Foot Cheetah

Бренд: Össur Страницы: 107

Бренд: Össur Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды